CCIE EI Section 2.1

[Siscco]

Found this useful thread.

This is the hidden content, please

• Sign In
• or
• Sign Up

[dds69]

thanks for your help guys

[zshengh]

Thanks champ

anytime!!

[Zoey]

thanks

[tinker123]

Thank for your help!

[visasman]

Very nice article. Thanks a lot!

For this task, does anyone know the exact steps? I could not get TACACS live logs from the Fabric switches, although my DNA is synchronized/managed with the Fabric switches and integrated with ISE.

[cnet123]

a

[visasman]

During my first attempt, I mentioned in my post that I skipped 2.1 and started 2.2, but I could not continue with 2.2 because the SDA border nodes were not synchronised which prevented 2.2. I did the synchronisation and then it went fine.

So, do check the sync part.

[kat]

Does it affect 2.2-2.5 score after completing 2.2-2.5 properly, if I make a mistake on 2.1?

[there]

Nice Threat

[johnnyboy]

Took the exam recently and it said the password needed a capital letter or something for the user password.  I guess we have to go in and change the password policy or something? Anyone think they mastered this question yet?

Edited April 4, 2023 by johnnyboy

[ShoIProute]

4 hours ago, johnnyboy said:

Took the exam recently and it said the password needed a capital letter or something for the user password.  I guess we have to go in and change the password policy or something? Anyone think they mastered this question yet?

Yes:

Administration>Identity Management/Settings>User Authentication Settings

Uncheck everything that would prevent u from using the username and pw that they want us to use.

 

[johnnyboy]

40 minutes ago, ShoIProute said:

Yes:

Administration>Identity Management/Settings>User Authentication Settings

Uncheck everything that would prevent u from using the username and pw that they want us to use.

 

Thanks, I ran out of time so didn't have a chance to dive into it.  Going to use this for next time!

[maxdieng]

Hello

[NTWMaster]

 

I found this on the cisco website.  I have not yet taken the lab but maybe this will help with the Tacacs part?  Radius is the default when configuring ISE in DNAC.  You can't use Tacacs in the Design module if you have not selected it when integrating ISE and 

Edited May 7, 2023 by NTWMaster

[NTWMaster]

Okay, I found one more document that may be helpful.  I will obviously know more once I finally take the lab OR someone could be kind enough to say this may be a solution.

 

 

Edited May 7, 2023 by NTWMaster

[NTWMaster]

.

Edited May 4, 2023 by NTWMaster

[johnnyboy]

Here are some rough steps that I put together from using my lab.  A lot of it depends on what is already configured in the lab. 

From what I remember in the lab I know for sure that TACACS was not enabled on the ISE server in DNA.

ISE
_____

Administration-> Deployment -> PSN -> Enable Device Admin Service -> SAVE
Administration-> Identity Management -> Settings -> User Authentication Settings -> Uncheck all password must contain at least: -> SAVE
Administration-> Network Resources -> Network Devices -> Click Devices -> "Check TACACS Authentication Settings" -> "Enter Shared Secret" 'cisco' -> SAVE
Administration-> Identities -> Users -> "Add" -> "Name: netadmin password: admin User Groups: ALL_ACCOUNTS" -> Submit
Work Centers-> Device Administration -> "View Default Policy" -> Authentication Policy -> "Internal Users" -> Options If User not found "Continue" -> Authorization Policy "Create New Command Set" called All_Commands -> Check Box "Permit any command that is not listed below" -> Shell Profiles "Create New Shell Profile" named Priv15 -> Default Privilege to "15" -> Submit
-> Select and Save both of these new policies

DNA
_____

System Settings -> Update ISE -> Click ISE server -> "Edit" -> "View Advanced Settings" -> Check TACACS -> Apply
Design -> Network Settings -> Add Servers -> AAA -> Check "Network" -> Choose ISE then Protocol "TACACS" -> Choose PSN -> SAVEDo this at Global Level. 

Make sure it applies to both branches
Provision -> Devices-> Select all 4 Switches -> Actions -> Provision Device
After Provision is successful:
Choose all four switches -> Actions -> Edit Device -> Change CLI to netadmin/admin

Test with SSH and DNA resync

 

@NTWMaster, let us know if you have any new design questions in that thread.

Edited May 10, 2023 by johnnyboy

[takak]

thx

[random147]

Awesome tips, ty

[mountaintop2]

On 5/10/2023 at 9:40 AM, johnnyboy said:

Work Centers-> Device Administration -> "View Default Policy" -> Authentication Policy -> "Internal Users" -> Options If User not found "Continue" -> Authorization Policy "Create New Command Set" called All_Commands -> Check Box "Permit any command that is not listed below" -> Shell Profiles "Create New Shell Profile" named Priv15 -> Default Privilege to "15" -> Submit

-> Select and Save both of these new policies

@NTWMaster, let us know if you have any new design questions in that thread.

Are you changing the Default Authorization Policy, or creating a new one above it? If creating a new one, what are you using for the condition?

[Cofffeee]

nice!

[egocogitoG]

ｔ