kat

I passed the design section and it was not new one?

Hello, I failed lab exam recently. This attachment is what I configured in the exam. I am skeptical about 1.15 and couldn't complete 2.1 and 2.5. but I got 80％ in SDN module from the report In section 3.2, I configured gateway address wrongly and Autmation section was 60％. Please check it and give me your advice. Thank you,

Does it affect 2.2-2.5 score after completing 2.2-2.5 properly, if I make a mistake on 2.1?

Yes, I have to move all tabs from "unread" status to "read" status. But they don't check your time stamp or log? i don't think that the score is just based on your configs

But 10.4.0.0/16, 10.5.0.0/16 = 10.4.0.0/15 so they are same. I am wondering if we use preconfigured one

Is this task for 1.8? and why is it needed?

If the question is to extend IPv6 connectivity, are these configs correct? Please check it R11 interface Ethernet0/0 ipv6 address 2001:2710:311::2/64 route-map NH permit 10 set ipv6 next-hop 2001:2710:311::1 router bgp 65001 address-family ipv6 neighbor 100.3.11.1 remote-as 10000 neighbor 100.3.11.1 activate neighbor 100.3.11.1 route-map NH in redistribute eigrp 65001 include-connected router eigrp ccie address-family ipv6 unicast autonomous-system 65001 topology base redistribute bgp 65001 metric 100000 10 255 1 1500 R3 vrf definition fabd2 address-family ipv6 route-target 10000:3681 interface gigabitEthernet1 ipv6 address 2001:2710:311::1/64 route-map NH permit 10 set ipv6 next-hop 2001:2710:311::2 router bgp 65001 address-family ipv6 vrf fabd2 neighbor 100.3.11.2 remote-as 10000 neighbor 100.3.11.2 activate neighbor 100.3.11.2 route-map NH in R4 vrf definition fabd2 address-family ipv6 route-target 10000:3681 mpls ldp router-id lo0 force interface loopback 0 ip address 100.255.254.4 255.255.255.255

In the lab, the prefix of Branches is already made and it is 10.4.0.0/16, 10.5.0.0/16. Can I just use it? Or do I need to make new prefixes of 10.4.0.0/15？

Is this enough? R24 router ospf 1 prefix-suppression summary-address 10.6.0.0 255.254.0.0 redistribute eigrp 65006 subnets tag 123

What do they check aside from your configs? Do they check exam logs and time, like when you configure, which question page you are looking at?

I have heard that someone didn't read the questions and solved all of them because he knew all questions and answers but he failed because CCIE checks the log. For example, when you open the question 1.2, you shouldn't configure 1.2-1.4 even if you know the question and answer. So you need to open 1.3 and 1.4 questions when you configure them. Is it true? Does CCIE check your log? And what else do they check and affect the score?

Are these correct? L2 Flooding should be used in conjunction with small address pools IP multicast routing with PIM-SM must be enabled

What is the answer in section 2.6?

Can SW400-510 be syncretized by skipping 2.1? Do I need some tasks before taking 2.2?

Thank you Can SW400-510 be syncretized by skipping 2.1? Do I need some tasks before taking 2.2?